AllMyPrinters

Your own slicer

Install the slicer, step by step

The app slices on our server by default. With the AllMyPrinters Slicer on your own computer, your models never leave your home. Pick your system, copy each line with one click and paste it. About 10 minutes.

Your settings

The slicer needs no password. It uses port 8080. Only change it if another program on that computer already uses 8080, the commands below adjust themselves.

Leave 8080 unless another program already uses it.

Pick your system

Not sure? A mini PC (like a NUC) or a Raspberry Pi with Ubuntu, Debian or Raspberry Pi OS counts as “Linux”. If you already manage your containers in Portainer, pick Portainer.

Linux: mini PC, NUC, Raspberry Pi, home server

  1. Open a terminal on the device

    Sitting at the device: open the Terminal app. From another computer: open PowerShell (Windows) or Terminal (Mac) and connect with SSH. Replace user with your user name on the device and the numbers with its IP address (your router’s device list shows it):

    The first time you connect, type yes. While you type the password, nothing appears on the screen. That is normal, just press Enter.

  2. Check that Docker is installed

    Paste this and press Enter:

    docker --version

    You see something like Docker version 27.3.1? Then go on to step 3. You see command not found? Then install Docker with this line, it takes a few minutes:

    curl -fsSL https://get.docker.com | sudo sh

    On a Raspberry Pi, also run uname -m. It has to say aarch64. If it says armv7l, the Pi runs a 32-bit system: install Raspberry Pi OS (64-bit) first.

  3. Start the slicer

    Paste this line. If sudo asks for a password, it is the one of your user on the device:

    sudo docker run -d --name allmyprinters-slicer --restart unless-stopped -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest

    The first start downloads the slicer with OrcaSlicer inside, about 500 MB, which can take a few minutes. At the end you see a long line of letters and numbers. That means it worked.

  4. Check that it runs and find the address

    Paste this:

    sudo docker ps --filter name=allmyprinters-slicer

    Under STATUS it should say Up, and after about a minute (healthy). Now get the address of the device:

    hostname -I

    The first number, for example 192.168.1.50, is the address. Continue below with “Test it in the browser”.

Update later

Run this line. It downloads the newest version and starts the slicer again. Do this when the app says the slicer is too old.

sudo docker pull ghcr.io/nolimitek/allmyprinters-slicer:latest && sudo docker rm -f allmyprinters-slicer && sudo docker run -d --name allmyprinters-slicer --restart unless-stopped -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest
Remove the slicer

Stops and removes the slicer:

sudo docker rm -f allmyprinters-slicer

To also delete its storage (only temporary jobs, nothing you need to keep):

sudo docker volume rm allmyprinters-slicer

Synology NAS (DSM 7.2 or newer)

  1. Install Container Manager

    In DSM, open Package Center, search for Container Manager and install it. If your DSM is older than 7.2, update it first: before 7.2 the package was called Docker and could not create projects.

  2. Create a folder

    Open File Station. In the shared folder docker (Container Manager created it), create a new folder named allmyprinters-slicer.

  3. Create the project

    Open Container Manager → Project → Create and fill in:

    • Project name: allmyprinters-slicer
    • Path: click Set path and pick docker → allmyprinters-slicer
    • Source: Create docker-compose.yml

    Paste this into the text box:

    services:
      allmyprinters-slicer:
        image: ghcr.io/nolimitek/allmyprinters-slicer:latest
        container_name: allmyprinters-slicer
        restart: unless-stopped
        ports:
          - "8080:8080"
        volumes:
          - allmyprinters-slicer:/data
    volumes:
      allmyprinters-slicer:
        name: allmyprinters-slicer

    Click Next. Leave the web portal (Web Station) switched off, click Next again and then Done. Container Manager downloads the slicer (about 500 MB) and starts it, which can take a few minutes.

  4. Check that it runs

    Under Container, allmyprinters-slicer should show Running. The address is the one you use to open DSM, without :5000, for example 192.168.1.50. Continue below with “Test it in the browser”.

Update later

Container Manager looks for new versions about once a day. When Image shows “Update available” next to the slicer, select it and choose Update.

Remove the slicer

Project → allmyprinters-slicer → Action → Stop, then Delete.

Unraid

  1. Make sure Docker is on

    Settings → Docker: “Enable Docker” has to be Yes. It is on by default.

  2. Open the terminal

    Click the terminal icon >_ at the top right of the Unraid web interface.

  3. Start the slicer

    Many Unraid containers already use port 8080. If one of yours does, enter a different port at the top first, for example 8081. Then paste this line and press Enter:

    docker run -d --name allmyprinters-slicer --restart always -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest

    The first start downloads the slicer (about 500 MB). At the end you see a long line of letters and numbers. That means it worked.

  4. Check that it runs

    In the Docker tab, allmyprinters-slicer now shows as started. Unraid marks it as a container without a template, that is fine. The address is the one of your Unraid server, for example 192.168.1.50. Continue below with “Test it in the browser”.

Update later

Unraid’s own update button does not work for containers started this way. Open the terminal and run this line instead:

docker pull ghcr.io/nolimitek/allmyprinters-slicer:latest && docker rm -f allmyprinters-slicer && docker run -d --name allmyprinters-slicer --restart always -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest
Remove the slicer

Stops and removes the slicer:

docker rm -f allmyprinters-slicer

To also delete its storage (only temporary jobs):

docker volume rm allmyprinters-slicer

Portainer

  1. Add a stack

    Log in to Portainer, pick your environment (usually local) and click Stacks → Add stack.

  2. Paste the slicer

    Name: allmyprinters-slicer. Build method: Web editor. Paste this into the editor:

    services:
      allmyprinters-slicer:
        image: ghcr.io/nolimitek/allmyprinters-slicer:latest
        container_name: allmyprinters-slicer
        restart: unless-stopped
        ports:
          - "8080:8080"
        volumes:
          - allmyprinters-slicer:/data
    volumes:
      allmyprinters-slicer:
        name: allmyprinters-slicer
  3. Start it

    Scroll down and click Deploy the stack. Portainer downloads the slicer (about 500 MB) and starts it, which can take a few minutes.

  4. Check that it runs

    Under Containers, allmyprinters-slicer should show running, and after about a minute healthy. The address is the IP of the device Portainer runs on, for example 192.168.1.50. Continue below with “Test it in the browser”.

Update later

Stacks → allmyprinters-slicer → Editor → Update the stack. In the dialog, switch on Re-pull image and redeploy and confirm.

Remove the slicer

Stacks → tick allmyprinters-slicer → Remove. If you like, also remove the volume allmyprinters-slicer under Volumes, it only holds temporary jobs.

Windows PC or Mac with Docker Desktop

  1. Install Docker Desktop

    Already installed, for example for another container? Then skip this step. Otherwise download Docker Desktop from docker.com, install it and start it.

    If the slicer should be ready whenever the computer is on, open Settings → General in Docker Desktop and switch on “Start Docker Desktop when you sign in to your computer”.

  2. Start the slicer

    Open PowerShell (Windows: Start menu, type “PowerShell”) or Terminal (Mac), paste this line and press Enter:

    docker run -d --name allmyprinters-slicer --restart unless-stopped -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest

    The first start downloads the slicer (about 500 MB), which can take a few minutes. If Windows asks whether Docker may use the network, allow it for private networks.

  3. Find the address of this computer

    Your phone needs it to reach the slicer.

    Windows: run ipconfig in PowerShell and take the IPv4 Address of your network adapter (Ethernet or Wi-Fi), for example 192.168.1.50.

    Mac: System Settings → Network → your connection shows the IP address.

  4. Check that it runs

    In Docker Desktop under Containers, allmyprinters-slicer should show as running. Continue below with “Test it in the browser”.

Update later

Run this line in PowerShell or Terminal. It downloads the newest version and starts the slicer again:

docker pull ghcr.io/nolimitek/allmyprinters-slicer:latest; docker rm -f allmyprinters-slicer; docker run -d --name allmyprinters-slicer --restart unless-stopped -p 8080:8080 -v allmyprinters-slicer:/data ghcr.io/nolimitek/allmyprinters-slicer:latest
Remove the slicer

Stops and removes the slicer:

docker rm -f allmyprinters-slicer

To also delete its storage (only temporary jobs):

docker volume rm allmyprinters-slicer

Then, on every system

  1. Test it in the browser

    On your phone or any computer in your home network, open http://<address>:8080/?a=version, for example http://192.168.1.50:8080/?a=version. You should see a short line with "name":"allmyprinters-slicer" and the OrcaSlicer version.

  2. Switch the app to your slicer

    In the app: More → Settings → Slicer → Own server. Enter http://<address>:8080, for example http://192.168.1.50:8080, and tap Connect.

    The app answers with “Connected: AllMyPrinters Slicer …”. From now on, every model is sliced at home.

  3. Using the agent?

    Then make the same setting in the agent: More → Settings → Slicer → Own server. Paired devices slice through the agent, at home and, with access from anywhere switched on, also on the go.

  4. Back to our server at any time

    More → Settings → Slicer → AllMyPrinters. Useful when your slicer computer is off.

Something doesn’t work?

“permission denied”

Put sudo in front of the command. In our Linux commands it is already there.

“The container name … is already in use”

The slicer is already installed. To start it with new settings, first remove the old container with sudo docker rm -f allmyprinters-slicer (on Windows, Mac and Unraid without sudo). Then run the start command again.

“port is already allocated”

Another program already uses port 8080. Enter a different number at the top, for example 8081, remove the container (see above) and start it again with the new command. Then use the new port in the app too.

“no matching manifest” or “exec format error”

The device runs a 32-bit system, and the slicer needs 64-bit. On a Raspberry Pi 4 or 5, install Raspberry Pi OS (64-bit).

The app says “No connection to …”

Is the phone on the same Wi-Fi as the slicer? Are address and port right? Open http://<address>:8080/?a=version in the phone’s browser: if that doesn’t load either, a firewall may block the port. On Ubuntu with ufw, run sudo ufw allow 8080/tcp. On Synology, allow the port under Control Panel → Security → Firewall.

The app says “No AllMyPrinters Slicer answers at …”

Something else answers at that address, usually another program on the same port. Check the port, or move the slicer to a different one (see “port is already allocated”).

The app says the slicer is too old

Update it, see “Update later” for your system.

Slicing fails or takes very long

Big multi-color models need a lot of memory. The log shows each job with “slice started”, “done” or “FAILED” and the reason: sudo docker logs --tail 30 allmyprinters-slicer.

Does my model go anywhere?

No. The slicer never connects anywhere on its own, and jobs are deleted after 24 hours. It has no password, so keep it in your home network and never forward its port to the internet.

Home Assistant OS, Proxmox, TrueNAS, OpenMediaVault, CasaOS?

Home Assistant OS doesn’t let you run your own Docker containers. Proxmox: create a small Debian or Ubuntu VM with Docker (4 GB of memory or more) and follow the Linux steps in it. TrueNAS SCALE, OpenMediaVault and CasaOS: open a shell over SSH and follow the Linux steps, or use Portainer if you have it.

Still stuck?

Tap “Report a problem” in the app and describe what happens. The last lines of the log help a lot: sudo docker logs --tail 30 allmyprinters-slicer.